Results 1 to 10 of 11
-
08-07-2012, 09:31 PM #1
Fishing line to tie down driftwood??
I want to use something more permanent to hold down my medium piece of driftwood. I have had it for about four years, but it never stays on the bottom. I have used cotton thread before, but it always ends up stuck in my filter intake.
Thank you for your thoughts.
-
08-07-2012, 09:39 PM #2
Fishing line is non-toxic, Works fine, & Is effectively invisible under water.
My GF calls me insincere... I pretend to care.
Think about how stupid the average person is and then realize that half of them are stupider than that.~George Carlin.
It's not that great.~Otto Rohwedder. My optimistic pessimism is tempered with pessimistic optimism.
Facts do not cease to exist because they are ignored.~Aldous Huxley.
“Always go too far, Because that's where you'll find the truth” ~ Albert Camus
-
08-07-2012, 09:42 PM #3
Another way to keep it on the bottom is to screw a flat piece of slate to the bottom of it and cover the slate with your substrate.
Liters to Gallons conversion calculator
"Keeping fish for any period of time doesn't make you experienced if you're doing it wrong. What does, is acknowledging those mistakes and learning from them." ~Aeonflame
" I like a spicy and flavorful BM" ~850R
"your argument is invalid." ~Mommy1
-
08-07-2012, 09:42 PM #4
Good! I am SO tired of the string.
I am going to try the fishing line. I prefer to keep metals out of my tanks, so the screws scare me. I thought about drilling a few holes through the wood, but the line sounds safer!Last edited by UofMKitty; 08-07-2012 at 09:47 PM.
-
08-07-2012, 10:09 PM #5
You can also silicone the slate to the driftwood
-
08-07-2012, 10:32 PM #6
A-1 to Kingfisher. I used the stainless screw/slate for a long time.
Cycling With Fish?•• The Fishless Cycle••
Goldfish Growth Expectancy••
The single biggest problem with communication is the illusion that it has taken place. "George Bernard Shaw"
-
08-07-2012, 11:01 PM #7
Member
Oscar
- Join Date
- Nov 2008
- Posts
- 524
Dental floss works too.
-
08-08-2012, 12:10 AM #8
If you've had the driftwood 4 years now and still hasn't sunk, it may take a lot longer for it to full submerge on its own. Drilling a hole into it and into a piece of slate is probably your best bet for a long term solution. Another option instead of a stainless steel screw is to use nylon bolts, have used those safely in aquariums before
-
08-08-2012, 02:34 AM #9
If it's already been in the tank for 4 years, chances are it will never sink. It could be a soft wood or a hollow wood.
Cycling With Fish?•• The Fishless Cycle••
Goldfish Growth Expectancy••
The single biggest problem with communication is the illusion that it has taken place. "George Bernard Shaw"
-
08-08-2012, 05:18 AM #10
The line is on!
The wood is finally secured to the bottom. I tried the silicone idea, but I guess the wood is as Lady Hobbs stated: hollow. Perhaps a little petrified, too considering all the drilling barely scratched the surface...LOL! Up until now, the best I could do was string and some rocks on top to hold it down, so the line has made me very happy! Thanks everybody for all your thoughts...I enjoyed mulling them all over!
-Give my best to fishies! ^_^





Reply With Quote
Red tailed catfish


Welcome to the New AC. Please be patient while I try to resolve all the bugs this update is sure to bring. In the end it will all be worth it!!
Cleaning...
Today, 06:14 AM in Algae