Results 1 to 10 of 15
Thread: about to pull my hair out
02-17-2013, 11:31 PM #1
about to pull my hair out
So I went with 2x 300w jagers. One is already set from my 75 g and the other i sat to the exact same numbers. Ok well at the moment i am keeping my heat at 60 because painters, electricians, and the carpenter have been in and out all day. at moment i have no lids. ok well it gets up to 77, and one heater turns off, my orginal jager, the new one never cuts off and then the other one comes back on. I know that the heat is probably escaping but the new one is at the exact same temp, so I figured it cut off a bit. I feel like I am throwing quarters out the window every minute. I am having trouble fitting a lid for the euro-braced, since the normal black newer tanks has that small brace that has grooves for the lids to fit in. the euro is just a straight piece of glass
02-19-2013, 12:26 AM #2Banned Goldfish
- Join Date
- Feb 2013
- Whidbey Island Washington State
You probably need to calibrate your heater
02-19-2013, 02:40 AM #3
Totally agree! If you don't bother to set it up right, You can't expect it to work
0Gas mileage isn't everything OIIIIIIIO
Lack of planning on your part does not constitute an emergency on my part.
Why pretend there are no stupid questions? Actually, There are many stupid questions: "Should I drink this bleach?" Is just one example.
Having said that, Just because it's a stupid question doesn't mean that it shouldn't be asked. It's better to know.
A warm beer is better than a cold beer. Because nothing is better than a cold beer, and a warm beer is better than nothing.
02-19-2013, 05:13 AM #4
+ to the above and will add that with all the painting and carpentry going on, can't you find some building material that you can temporarily place over the top of the tank to help keep the heat in? If nothing else, get a big black garbage bag, leave it flat and fix it over the top with tape or something - leaving a space in the back or front for air exchange.
You could go to hobby lobby and for less than $20 get a couple pieces of thin plexiglass and set them over the top to help keep the heat in.
Good luck!30 g FW planted:corys, female ABNP, blue angel, harleys, zebra danios, rummies, mystery & assassin snails
15 g FW planted:2 male guppies, neons, pygmy corys, clown pleco, 4 types of shrimp, mystery & assassin snails
90 g FW planted:congos, rainbows, roseline sharks, kribs, male ABNP, peppered cories, assassin snailss
90 Gal Journal: http://bit.ly/1vC7gVX
fishless cycling: http://bit.ly/1DARf3T
fish in cycling: http://bit.ly/1ILvcfp
02-19-2013, 12:14 PM #5
find some styrofoam. should be easy enough to at least insulate the top and keep out debris.your friendly neighbourhood arowanaman!
02-19-2013, 08:15 PM #6
Not to sound like a smart@ss yall, but i know how to calibrate and have been doing it for several days trying to get it right. I figured if they were set the same they would go on and off and the same time. I finally got79.9 to 80.1 desired but it goes off for a minute then stays on for 5. and i do have like a 1/2 thick instalation on top. also repairs are upstairs. getting lid tomorrow BUT no body has answered the big question how do i do lids with the euro bracing. I mean i can get the glass cut and i have some of the bending stuff to do 2 seperate pieces. but on side that will be toward the middle of tank it has no brace but a piece of glass. if the glass is held front, back and on the side, can it hold itself on that side were it meets the euro braced glass
02-19-2013, 08:33 PM #7Member Oscar
- Join Date
- Nov 2008
You will never be able to set them both to the exact same temperature. One will always turn on before the other.
If the heaters are sized that one alone can maintain the temperature, then one will remain permanently off and the other will cycle on & off.
If the heaters are sized that both are needed to maintain the termperature, then one will remain permanently on and the other will cycle on & off.
02-19-2013, 08:49 PM #8
02-19-2013, 09:04 PM #9
ignore the setting on the dial on the heater.
Place one heater in a large container of water (or QT tank) with accurate thermometer that you can trust. Keep adjusting the temp dial on the heater until the water is heated up to the temperature that you want according to your thermometer. Just make sure you wait about 15 minute after adjusting the dial before you check the thermometer to get a accurate temperature reading. Once the water has the stable temperature that you want, place that heater in the tank and complete the same process for the next one
The above has always worked for me.If you take your time to do the research FIRST, you can successfully set-up and keep ANY type of aquarium with ease.
"Not using a quarantine tank is like playing Russian roulette. Nobody wins the game, some people just get to play longer than others." - Anthony Calfo
Fishless Cycle Cycling with Fish Marine Aquarium Info [URL="http://saltwater.aquaticcommunity.com/"]
02-19-2013, 09:08 PM #10
Thanks cliff. I will do that tomor. I know one is fine since it kept my 75 a constant 81 but the new one is a bit off apparently