should i consider getting a new filter

**Shidohari** · 02-03-2013, 02:21 PM

my bedroom tank filter had stopped sucking water into the filter box last night. ( i caught it same night). After trying to see what was wrong apparently i tapped the filter on the side the right way and the suction started going again. I refiled the water box in the filter (marineland penguin 100) and it's still running this morning.

My current filter is handling the bioload in this tank as this was a tank that i completed a fishless cycle on. I just am concerned that the filter would go out again when i'm not home to catch it. This was also the same power filter i had issues with when i put the kit together initially prior to starting my fishless cycle in the tank. it also takes forever to start it's job after i do a WC usually 5-10 minutes and i use the tank water to fill the box to start it up.

Current stocking in this tank is 6 flame tetras, 4 ornate tetras, a nerite snail and a mystery snail. I have already upped the Water changes to 50% twice a week to ensure the nitrates are kept down as that is the only thing showing any reading at this time. Both ammo and Nitrites have been Zero.

the problem is i need to either keep the same type of filter (so i can transfer the media in the box over so i don't lose my cycle or upgrade slightly to one with enough room in the filterbox to accomodate both the old A pad i have now and whatever pad they require in the filter system.

I'm open to options on this as long as i can transfer the media in the biowheel and the blue sponge over.

I would be using part of my tax refund money to get the filter. (was thinking of upgrading to a penguin 150 which is supposed to be good with up to thirty gallon tanks. penguin 150 uses a B size sponge filter though)

Thoughts?

**eltylT** · 02-03-2013, 02:51 PM

you could clean the impeller and bottom of the filter box . i too have had that happn but after cleaning the impeller and hole at bottom of box it has ran well for past 3 years . filter is about 10 years old and needs cleaning out 4 times a year or at least that what i do.

**Shidohari** · 02-03-2013, 03:56 PM

i don't see the impeller on mine and it did take forever to start. i will keep an eye on it. where would the impellor be in the penguin 100?

**Goes to 11!** · 02-03-2013, 04:09 PM

Originally Posted by Shidohari

i don't see the impeller on mine and it did take forever to start. i will keep an eye on it. where would the impellor be in the penguin 100?

It's the only moving part that's powered, When you are trying to get 'it' started.. The 'it' IS the impeller.

Look in your manual. It's diagrammed in an exploded view as part 6 on page 6. [Or here:http://www.aquariumpart.com/v/vspfil...in_manual.pdf]

**Taurus** · 02-03-2013, 07:15 PM

I don't know if this helps, but here is a link to the marineland website and its page for penguin filters. At the left of the page, part way down, the is a link to a video on maintaining a penguin filter.

http://www.marineland.com/Products/a...er-filter.aspx

HTH

**Shidohari** · 02-03-2013, 08:22 PM

on the penguin 100 hundreds you can't remove the impeller as it's built into the housing (intake tube goes in over the impeller section tried using my fluval planting tongs to reach down gently to see if i could pull it out) .

However i was able to get a clean qtip into the access slot where it is and get some of the slime off of it. then put it back together, it started up immediately. I don't know if that's because it was only unplugged for a short time, or if the slime removal actually made some difference.

Time will tell though the video taurus posted DID help