Type: Posts; User: Gone_Fishing; Keyword(s):
Search: Search took 0.01 seconds.
So far I have 6 rumming nose, 6 cory cat. Ton of plants.
Bumble bee cat.
I'm looking for something more colorfully.
02-03-2012, 07:43 PM
Are they jumper? Thinking of buying 1
Is the 20-40 bigger then the 30-60?
Been a while but got almost everything done.
Just some pic.
After putting the tank on the stand I went ahead and build a light holder for my 3 light.
Made from pvc pipe, y pvc? Cause pvc is...
I bought 2 bag of this stuff. I found some stuff in there as well, look at pic below.
Can someone who have use this stuff tell me if all bag are like that.
My first time using black diamond sand.
So far got the 2 frame done, still need to cut down the legs to 23 1/2 inch so all legs match. I knew I should of bought a miter saw for x-mas now the price went up.
I got all my 2x3 cut out. Sadly the dude that cut my lumber didn't do a job at it.
Out of 10 legs he only got 2 cut at 24inch.
The other 8 are off by 1-2 cm now I'm upset.
A waste of 2 lumber.
Anyone use or own a Kreg Jig?
what kinda screws do you use?
kreg jig screws r a bit over the price for me. will dry wall screws be fit?
I want to build a stand for my new 40B
here is my plan...
Stand H = 29 inch
Stand L = 36 3/8
Stand W = 18 3/8
Here a List of my Cut.
i will be using 2 by 3
Do I have to use plywood?
Can I just sit the tank right on top of the 2x3 without adding a sheet of plywood?
I'm going to just cover the stand up with a sheet of cotton.
Thanks ill just have to build one.
Will 2by3 be good? I have lots of 2by3 left over.
Will that work or will it cause to much stress to the stand?
The stand is one of those wood stand u buy from performance made from them heavy cheap plywood.
I'm thinking of setting it up in the...
12-17-2011, 02:55 AM
I got a question.
If I was to use a Regulator will I still need a ASA?
Can someone tell me if this the right stuff, link below.
Just took 3 more pic.
The black stick is pointing at the chip spot.
I post this on other forum as well but heaven't got a good answer yet.
I want to ask you ppl here.
I took off all the silicone in my 75, after taken mins trying to removed the corner I found
I just paint the tank with roller but problem is if you shine a light inside the tank u can see light. Should I wait till dry n re paint it?
Anyone know how to get smoke cig. Smell off?
The stand tend to smell after being outside for 2 days.
The t12 doesn't blink but the t8 does.
Both ballast do look old but still work.
The t8 bulb are brand new. I wait for couple of sec maybe 30 sec the most.
Hmm how come my tank light keep blinking when I install my t8 into them?
The ballast do say its for t12, t8.
Been doing a lot of reading on planted tank. Net about lighting.
Seem like I can just used my t8 shop light to grow plant.
Do it make any different if I use my 48" light that came with the tank...
The black knife is 4-5 inch he/she is inside my 20gallon QT tank.
Got him from petsmart so gotta QT.
I also got half inch fry in the 20 gallon as well, very single one is there.
I been doing a lot a lot review on odyssea cfs-500 and the t5ho.
For 120 total shipped I'm thinking of buying them off ebay.
Buying the t5 is better then DIY the t8 into a t5 and would save me a...
I want to start this thread base on my 75g I just got
So far so good. Tank is being leak test outside till wed then dry it up once dry paint the back black.
I'm going to use black sand in this...
I end up buying the tank. It's the hood not the tank.
Tank is filling up as I type here. Doing a test leak before I bring it inside for set up.
The silicone look kinda used up should I re- seal the...
If its the hood I wouldn't care as I'm going to sell it off or throw it with my junks.
I like hoodless better or glass top.
Hopefully he meant to say hinges. Will make my drive a worth driving.